Homepage » Technology » Products »

Checking power semiconductor devices in production line

Insight into the inside: x-ray inspection of solder quality
Checking power semiconductor devices in production line

Ixys UK Westcode, part of the power semiconductor manufacturer, Ixys Corporation, is investing in its Chippenham, UK factory to manufacture a new range of power semiconductor devices, which will be marketed alongside the company‘s press-pack capsules. Nikon Metrology was chosen to supply the x-ray equipment for checking the quality of the reflow soldering process during production.

Power semiconductor devices are used for switching high currents and voltages and are widely used in the rail, wind turbine, mining, and petrochemical sectors. Press-pack capsules are clamped together under high pressure to achieve the required electrical rating, whereas isolated power modules use integrated circuit on DCB (direct copper bonded) substrate technology. The Metrology XT V 160 is needed because the reflowed solder, which attaches the chips to their contact pads, must be continuous with a controlled level of voids and x-raying is the only way to see if these conditions have been met.

Fiona Lambert, Process Engineer at the company commented, „I previously used a smaller Nikon 130 kV x-ray quality assurance (QA) system when I worked at an electronics company in South Wales, so I knew how easy their equipment is to use. After reviewing what else was on the market, it was clear that the 160 kV model would best suit our application, which involves penetrating thicker and higher density materials to observe solder coverage.

„What I particularly like about this system is the easy access to the large stage, which allows me to place several, quite large components on it at the same time. The machine is fast in operation and the stage is easy to manipulate in multiple axes, so tilting, rotating and positioning, as well as, zooming the image on the screen is rapid. You can see everything clearly, as the image is in high resolution. The software is also user-friendly and even works out automatically the percentage of voids in the solder, required to ensure the product meets rigorous specifications.”

Two-step x-ray inspection

X-raying is carried out at two stages of manufacture. The first is after the chips have been placed on the blank DCB substrate and reflow soldered. After six built substrates have been electrically tested and soldered onto a 5 mm thick aluminum-silicon-carbide baseplate, the whole assembly is x-rayed again.

The system inspects the assembly reliably, even without the optional x-ray laminography software or CT (computed tomography) add-on. Features of the machine that assist in completing the task efficiently include its 20 watt target power rating, focal spot size between 1 μm and 10 μm depending on power output, up to 36,000x system magnification and the high image quality provided by a Varex 16-bit flat panel. Having such fine resolution allows easy distinction between geometrical shapes and the amorphous voids.

Multiple uses: x-ray system inspects quality of incoming materials

While the x-ray machine was installed specifically for DCB inspection, its presence on the Chippenham site has proved beneficial for verifying the quality of bought-in materials. On one occasion, a supplier disputed that there was a high incidence of solder blockages in a consignment of delivered coolers that form part of press-pack IGBT stacks. A simple analysis using the inspection machine provided irrefutable evidence and resulted in the prompt arrival of a replacement batch.

Open-tube x-ray source design reduces maintenance cost

An additional advantage of the x-ray technology is the stability of output due to the micro-focus spot source and advanced image processing capabilities, essential to avoid degradation of image quality. Focus of the electron beam is maintained by a computer-controlled, electromagnetic lens that ensures the target does not overheat whilst maintaining a micron spot size, even at high kV settings.

Although a high power machine, the XT V 160 is of open-tube design. As part of planned maintenance, replacement of the electron beam-producing filament can be scheduled a couple of times per year for a cost of a few pounds. Filament replacement takes minutes, so downtime is short. A sealed tube, on the other hand, will last for a couple of years but can stop working without warning, perhaps at the worst possible time for the user. The manufacturer then has to be called in to renew the tube at a high cost and the machine is down for days.

Conclusion

The company’s inspection of power semiconductor devices will increase over the coming years. With one or two products per batch to be x-rayed for QA, the Nikon Metrology machine will be in constant use once the process has been finally established. As a postscript, it is interesting to note that the transmission target x-ray source in this particular system is the 1,000th to be manufactured in the UK at the Tring factory since manufacturing began there in 1987.

SMT Hybrid Packaging, Booth 4–308

www.nikonmetrology.com; www.westcode.com


Tip

A video of Fiona Lambert talking about the advantages of the system: www.youtube.com/watch?v=0Uy9T13Y6_E&feature=youtu.be


Zusammenfassung Résumé Резюме

Nachdem die Inspektion von Leistungshalbleitern eines Herstellers in den kommenden Jahren eine zunehmende Tendenz zeigt, wurde zur Prüfung einer neuen Produktreihe von Leistungshalbleiter-Modulen in Röntgen-Equipment von Nikon investiert. Damit soll die Qualität während des Reflowlötprozesses überprüft und gesichert werden, wie der Anwenderartikel zeigt.

Après une tendance croissante dans l‘inspection des semi-conducteurs de puissance d‘un fabricant au cours des prochaines années, Nikon a investi pour mettre au point une nouvelle gamme de modules de semi-conducteurs de puissance dans l‘équipement à rayons X Nikon. Le but est de vérifier et de sécuriser la qualité pendant le procède de brasage par refusions, comme le montre l‘article de l‘utilisateur.

Поскольку инспектирование силовых полупроводниковых приборов в ближайшие годы станет стандартной процедурой, при запуске новой линейки силовых полупроводниковых модулей было принято решение инвестировать в рентгенографическое оборудование Nikon. В статье рассказывается о том, каким образом обеспечивается контроль качества при пайке оплавлением.

Current Issue
Titelbild EPP EUROPE Electronics Production and Test 11
Issue
11.2023
READ
Newsletter

Subscribe to our newsletter now

Webinars & Webcasts

First hand technical knowledge

Whitepapers

Find all current Whitepapers here

Videos

Find all current videos here


Industrie.de Infoservice
Vielen Dank für Ihre Bestellung!
Sie erhalten in Kürze eine Bestätigung per E-Mail.
Von Ihnen ausgesucht:
Weitere Informationen gewünscht?
Einfach neue Dokumente auswählen
und zuletzt Adresse eingeben.
Wie funktioniert der Industrie.de Infoservice?
Zur Hilfeseite »
Ihre Adresse:














Die Konradin Verlag Robert Kohlhammer GmbH erhebt, verarbeitet und nutzt die Daten, die der Nutzer bei der Registrierung zum Industrie.de Infoservice freiwillig zur Verfügung stellt, zum Zwecke der Erfüllung dieses Nutzungsverhältnisses. Der Nutzer erhält damit Zugang zu den Dokumenten des Industrie.de Infoservice.
AGB
datenschutz-online@konradin.de